







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Asphalt Driveways & Resurfacing in Alamo, CA: What It Actually Takes
Asphalt driveways & resurfacing in Alamo typically run $3,500 – $9,000 for a full paving job and $250 – $700 for a reseal, with most residential driveways finished in one to three days depending on size and slope. A driveway replacement, where the old surface comes out entirely, lands between $5,000 and $14,000. Call (855) 471-4163 and we’ll walk your driveway, measure it, and tell you straight whether you need a resurface or a rebuild.
How We Pave or Resurface an Alamo Driveway, Stage by Stage

Every driveway we build in Alamo follows the same sequence, because skipping a stage is how asphalt fails two winters later. Here’s what happens and when.
Stage 1: Walkthrough and measurement (day of estimate)
We measure square footage, check the existing base, and look at how water moves across the slab. On Alamo’s sloped lots, drainage is the whole ballgame. You’ll decide at this point whether you’re resurfacing over sound asphalt or tearing out to the base. A written, line-item estimate follows within a day.
Stage 2: Demolition and removal (day 1)
If it’s a replacement, we break out the old surface and haul it off. We also cut back any failed base material. On a one-acre-plus lot off Stone Valley Road, that can mean a long run of driveway and a full day of hauling alone. You’ll confirm access for the dump truck and where equipment parks before this stage starts.
Stage 3: Grading and base prep (day 1 into day 2)
This is the part nobody sees and the part that determines whether your asphalt lasts. We re-grade for positive drainage away from the garage, compact the aggregate base in lifts, and check slope. On hillside lots the grade work runs longer. This is where you approve any drainage corrections we find.
Stage 4: Paving (day 2 or 3)
Hot-mix asphalt goes down at 2 to 3 inches compacted for a residential driveway, rolled while it’s hot. Edges get true and the surface gets its crown. The driveway is not drivable for 24 to 48 hours, sometimes longer in hot weather while it cures. Plan to park on the street or a neighboring pad.
Stage 5: Seal and cure (30 to 90 days out)
New asphalt needs to cure before sealing, usually a month to three months. We schedule the seal coat as a separate visit. This is also when you decide whether to add a widened turnaround or a decorative border. Our technicians have up to 12 years of experience on asphalt work, and the whole job is covered by our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Asphalt Options You’ll Choose Between
Most of the decisions on an Alamo driveway come down to a handful of real choices. Here’s the honest trade-off on each.
- Resurface over existing vs. full replacement: Resurfacing is cheaper and faster, but only if the base is intact. Patch a cracked base and the cracks telegraph through within a year. Replacement costs more upfront and lasts decades. If more than a quarter of the surface has failed, we’ll tell you to replace, not resurface.
- Hot-mix asphalt thickness: 2 inches compacted suits a light-use residential driveway. 3 inches is worth the added cost for a long drive or a turnaround where heavier vehicles turn. The difference in base and thickness is what separates a 15-year driveway from a 30-year one.
- Aggregate base depth: 4 inches is the floor for stable soil; 6 to 8 inches is common on Alamo’s clay-heavy foothill lots. Alamo’s clay swells with winter moisture, so a deeper base and geotextile fabric are cheap insurance on a sloped lot.
- Seal coat finish: A standard emulsified seal costs $250 – $700 and protects the binder from UV. Skip it for a few years and the asphalt turns gray and ravels. You’ll reseal every two to three years.
What Asphalt Driveways & Resurfacing Costs in Alamo, CA

A full asphalt paving job in Alamo runs $3,500 – $9,000, a complete replacement with base work runs $5,000 – $14,000, and a reseal runs $250 – $700. Those ranges hold for most standard residential drives; five variables push a job toward the high end.
- Square footage and slope: A long, steep drive off the ridges needs more asphalt, more base, and more grading than a flat one. Grade is often the biggest swing.
- Base condition: If the existing base is sound, resurfacing is cheap. Failed base means tear-out and rebuild.
- Drainage corrections: French drains, swales, and culverts add cost, but skipping them causes erosion on hillside lots.
- Access and haul-off: Tight or long driveways slow demolition, and hauling adds truck time.
- County and fire-district review: Grading on sloped lots may trigger county review, which adds time and permit cost.
A written estimate itemizes base prep, asphalt tonnage and thickness, haul-off, and seal coat timing. It does not usually include drainage corrections found during excavation or a decorative border. Our pricing is upfront, so the number you see is the number you pay, and 0% financing for 18 months plus $1,000 off projects over $10,000 is available.
See the difference
Before
After
Before
After
Before
AfterWhy Alamo’s Foothill Lots and Houses Change This Job
Alamo isn’t like paving in a tract subdivision. It’s an unincorporated part of Contra Costa County, which means permits and grading review go through the county, not a city building department. On the wooded, steep-graded lots off Stone Valley Road and along the ridges, that review can hinge on hillside grading rules and fire-district clearance as much as the paving itself. Many driveways here are long, so drainage runs the wrong way and erosion eats the edges during winter rains. The 1960s through 1990s custom homes on one-acre-plus lots frequently have asphalt that’s near the end of its life. We see edge crumbling, alligator cracking from shallow base, and water pooling at the garage apron. If your project is part of a full Driveway & Pavers in Alamo scope, or you’re considering materials, our Driveway & Pavers service covers the wider picture. We cover all of Alamo, and homeowners often pair this with a Chain Link Fence in Alamo at the same time, or plan a driveway as part of ADU Site Prep & Utilities in Alamo.
Serving Alamo, CA – Our Local Coverage Area
We serve Alamo and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Asphalt Driveways & Resurfacing in Alamo

Asphalt driveways & resurfacing in Alamo run $3,500 – $9,000 for paving and $5,000 – $14,000 for a replacement with base work. Resealing is $250 – $700. Call (855) 471-4163 for an exact quote; estimates are free.
Most Alamo driveways are finished in one to three days, plus 24 to 48 hours of curing before you park on it. Sealing happens 30 to 90 days later. The whole schedule depends on size, slope, and haul-off access.
A simple resurface usually doesn’t; a full replacement that changes grade or drainage on a sloped lot in unincorporated Contra Costa County may. We check with the county during the estimate so nothing surprises you mid-job.
Yes, when the base is sound and less than a quarter of the surface has failed. If the base is soft or cracking from underneath, resurfacing is money down the drain.
Every job carries our 730-Day Done Right Promise. If the workmanship isn’t right within that window, we make it right. Call (855) 471-4163 to schedule.
Get a Free Estimate for Asphalt Driveways & Resurfacing in Alamo
Call (855) 471-4163 to schedule a free on-site estimate for your asphalt driveways & resurfacing project in Alamo. We measure the drive, check the base and drainage, and hand you a written line-item quote so you know exactly what you’re paying for. Calls are answered by a live person 24/7, and financing is available. We’re ready when you are.
Written by the team at Groundwork Construction Co.












