







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Paver Driveways in Ashland, CA
A paver driveway in Ashland typically runs $7,000 to $18,000 and takes three to five days of on-site work, from demolition through the last compacted joint. What you get is a surface that moves with the ground instead of cracking against it. In a town built on the Hayward Fault, that distinction matters more than any sales pitch. Call (855) 471-4163 to schedule a free on-site estimate, with a written line-item quote you can compare against anyone else’s.
How a paver driveway goes in, stage by stage

We don’t hand you a vague “we’ll get started Monday.” Here’s the actual sequence, so you know what to expect on each day and what decisions land in your lap.
Stage 1: Site review and measurements (day 1, under an hour). We walk the existing driveway, check the slope and how water drains off it, look at what’s under the surface if there’s any question, and confirm the paver layout with you on paper. This is where you lock in whether you want a herringbone or running-bond pattern, whether we’re running pavers up to the garage door or leaving a transition strip, and whether drainage is going to need a channel drain. We also confirm the permit path, which in Ashland means a call to Alameda County, not a city counter.
Stage 2: Demolition and haul-off (day 1, two to four hours). The old surface comes out. If it’s concrete, we break it out with a breaker and load it; if it’s cracked asphalt, it comes up in sections. You don’t have to decide anything here, but you do want to be around to see the condition of what’s underneath. Soft spots or a failing base show up now, not later.
Stage 3: Base prep and compaction (day 2, the longest day). This is the stage that determines whether the driveway holds up for a decade or starts to settle in two winters. We excavate to the right depth, build a graduated gravel base, and compact it in lifts, not all at once. For a residential driveway that’s usually six to eight inches of compacted aggregate. A geotextile fabric goes down over the subgrade underneath. We check grade against the garage floor and the street so water runs where you want it. Nothing about the final look matters until this stage is right.
Stage 4: Setting bed and laying pavers (day 3, most of the day). We screed a one-inch sand or fine-chip setting bed, then lay the pavers in your chosen pattern, cutting edges to fit with a wet saw. On a tight residential street with limited frontage, a paver crew will typically set 600 to 900 square feet in a day. You’ll want to be on hand to confirm the border and any accent rows before the edges go in.
Stage 5: Edge restraint, compaction, and joint sand (day 4, two to three hours). A spiked edge restraint goes around the perimeter so the field can’t creep, then the surface gets compacted and swept with polymeric joint sand, which sets up hard and keeps weeds and ants out. Final walkthrough with you, and we point out where to top off the joint sand in the first season if the surface settles.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll weigh before you sign
A paver driveway isn’t one product. What you choose changes both the look and the number.
- Concrete paver vs. clay brick vs. travertine. Concrete pavers are the default for value and durability and account for most of the Ashland market. Clay brick costs more but holds color for decades. Travertine looks premium but is slick once wet and needs more sealing in the East Bay’s winter rain. For most of the homes here, a good concrete paver with a proper base is the sensible call.
- Grade and construction. The best concrete pavers are rated for heavy vehicular traffic and hold up for 30+ years. Cheaper ones run thinner and can spall or chip within a decade in the freeze-thaw cycles we don’t get often but do get. Ask for the manufacturer’s traffic rating, not a sales line.
- Pattern. Herringbone and running bond take more cuts, so they cost more in labor but drain and interlock better. Basketweave and stack bond are simpler and faster. A herringbone with a border is the pattern most Ashland homeowners land on for a front driveway.
- Base and drainage. You can cut corners here and it’ll look identical on day one. The honest trade-off: a thinner base saves a few hundred dollars and costs you the driveway in five years. Ask any quoted base depth and compaction method.
- Permeable pavers. Worth considering if the driveway is over a thousand square feet or drains toward the house. Higher upfront cost, and Alameda County has been steadily raising stormwater treatment requirements, so it can help with plan check.
What Paver Driveways costs in Ashland, CA

A paver driveway in Ashland runs $7,000 to $18,000 installed, depending on size and finish. Here’s what pushes the number up or down:
- Square footage. A single-car driveway runs toward the $7,000 end; a wide double with room for a second vehicle pushes the upper half of the range.
- Existing surface. Removing and hauling a thick concrete slab costs more in labor and disposal than scraping off asphalt.
- Base condition. A failing subgrade means more excavation and more base material. If the old driveway has heaved or sunken, we catch it at Stage 2 and it adds to Stage 3.
- Paver selection. Premium clay or travertine can run a third more than concrete in material alone.
- Drainage. Channel drains, tie-ins to existing storm lines, or a regrade of the adjacent yard.
- Permit scope. Most residential paver driveways are straightforward, but any drainage changes to the street shoulder trigger a longer county review.
Your written estimate should itemize labor, base depth, paver type and quantity, edge restraint, joint sand, and disposal. If any of that is missing from a bid, ask for it. Our estimates also come with no-hassle upfront pricing, so the number in writing is the number you pay, and 0% financing for 18 months is available if you want to spread it out. If you’re considering pavers as part of a bigger project, see our Driveway & Pavers service for the full range of hardscape work, or the Driveway & Pavers in Ashland page for the broader picture.
See the difference
Before
After
Before
After
Before
AfterWhat Ashland homes specifically do to a paver driveway
Ashland sits in unincorporated Alameda County, so a paver driveway here runs on County Building Department permits and inspection schedules. That’s a different counter, a different plan-check queue, and different inspectors than you’d deal with one street over in Hayward or San Leandro. It’s a jurisdictional detail most contractors learn the hard way, and it shapes how fast your job moves from contract to ground-break. The housing stock adds to it: mid-century ranch homes and small stucco duplexes built from the 1940s through the 1970s dominate here, many with detached garages, original early wiring, and unpermitted additions that need to be worked around when the driveway ties into existing utilities. And because the Hayward Fault cuts right through the area, older foundations and cripple walls are common, which means a paver driveway that meets a settling slab will telegraph that movement through the pavers at the joint. We see it most on the older streets off East 14th and in the flat blocks near the 94578 ZIP, where the original concrete has been patched three times over fifty years. East Bay rain comes off the bay in concentrated winter storms, so drainage and base compaction do more for the life of a paver driveway here than any surface choice. We cover Ashland and the surrounding East Bay neighborhoods, and we treat the county permit path as part of the job, not a favor.
Serving Ashland, CA – Our Local Coverage Area
We serve Ashland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked about Paver Driveways in Ashland

Most Ashland paver driveways are finished in three to five on-site days, with the county permit adding one to two weeks before ground-break. A typical single-car job runs shorter, and a large driveway with drainage work runs longer. Call (855) 471-4163 to get a timeline for your specific layout.
Yes, most paver driveway installations in Ashland require a permit through the Alameda County Building Department because you’re modifying a hardscaped surface and often the drainage pattern. We pull the permit and handle inspections as part of the job. Call (855) 471-4163 if you want us to confirm the requirements on your property.
Expect $7,000 to $18,000 for a residential paver driveway in Ashland, with the lower end for a single-car install over an existing base and the upper end for a large double driveway with upgraded material and drainage. Call (855) 471-4163 for a written line-item quote, free of charge.
In some cases, yes, but only if the existing concrete is sound and stable. If it’s cracked, heaved, or has failed at joints, pavers laid over it will telegraph that movement within a season. We check it during the site visit and tell you the honest answer. Call (855) 471-4163 to have us out to take a look.
Our paver driveway installations are covered by the 730-Day Done Right Promise, one of the longest workmanship guarantees in the residential construction space. If something we installed isn’t right, we fix it, full stop. Call (855) 471-4163 to talk through the details.
Ready for a real number on your paver driveway?
We’ll come out, measure the existing driveway, look at the base and drainage, and hand you a written line-item estimate for a paver driveway in Ashland. The visit is free, the quote is free, and you’ll get the honest answer on what your existing surface will and won’t allow. Call (855) 471-4163 to schedule yours, and we’ll confirm the county permit path on your property before you commit to a dollar figure.
Written by the team at Groundwork Construction Co.












