







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Alamo: What It Costs and How Long It Takes
Concrete driveway installation in Alamo typically runs $4,500 – $12,000, and a full replacement lands between $5,000 – $14,000, with most jobs finished in 3 – 5 working days plus a 7-day cure before you park on it. Call (855) 471-4163 and we’ll come out, measure, and hand you a written line-item quote at no charge. The rest of this page covers how the work actually runs, what drives your number up or down, and why Alamo lots complicate concrete in ways flat lot cities don’t.
How concrete driveway work runs, step by step

Concrete is unforgiving of shortcuts. Once it sets, every prep mistake lives under the slab for decades. Here’s the sequence we follow, and where you make decisions.
Stage 1: Layout and site check (day 1, about 2 hours)
We walk the grade, mark the pour boundaries, and check the slope against what your drainage actually does in a winter storm. On hillside lots, this is where we confirm whether the driveway drains toward the house or away from it. You confirm width, apron placement, and whether you’re keeping the existing curb cut.
Stage 2: Demolition and haul-off (days 1 – 2)
Old slab comes out, rebar and all, and the spoils leave the property. Most Alamo driveways run 400 – 900 square feet, so expect a half day to a full day of breaking and roughly a dozen truckloads of debris on a longer drive. You don’t have decisions here, but you should know your lawn edge and landscaping will take some traffic.
Stage 3: Grading and base prep (day 2 – 3)
We excavate to depth, compact the subgrade, and lay 4 – 6 inches of compacted aggregate base. This is the stage that decides whether your slab cracks in year three or holds for thirty. On sloped lots we form step-downs and adjust the base depth so the finished surface stays walkable and drainable. You approve the final pitch before anything gets poured.
Stage 4: Forms, rebar, and inspection (day 3)
Forms go in, rebar or mesh gets tied at the spacing the pour requires, and if your job needs a county permit, the inspector signs off on grading and reinforcement before we pour. Skipping that inspection is the single most common shortcut we get called to fix later. You see the steel layout and confirm the control-joint pattern before we order concrete.
Stage 5: Pour, finish, and cure (day 4 – 5, then 7 days)
Concrete arrives, gets screeded, floated, and finished in whichever texture you chose. Control joints go in within 24 hours. Then it cures: no vehicles for 7 days, no heavy loads for 10. You pick the finish and the joint layout the day before, and we hand you a cure schedule in writing so nobody parks on it early.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The concrete and finish options you’ll choose between
Most of the decisions on this job come down to mix and finish. Here’s the honest trade-off on each.
- Standard 4-inch broom-finished slab: The workhorse. $4,500 – $8,000 on a typical Alamo drive. Textured enough for wet-season traction and cheap to maintain. Best for flat or gently sloped approaches.
- 6-inch reinforced slab: Thicker pour with rebar grid. Runs $7,000 – $12,000. Worth it on any drive that takes an RV, boat trailer, or heavy truck, and on slopes where flex cracking is a real risk.
- Exposed aggregate: Pea gravel surface revealed by washing the top layer. Adds $2 – $4 per square foot over broom. Excellent grip on steep hillside drives, but harder to shovel and rougher on bare feet. Note that stamped and decorative concrete has its own page on this site.
- Fiber-reinforced mix: Synthetic fibers blended into the pour to reduce plastic shrinkage cracking. Modest upcharge, no visible downside, and a smart add on hot-summer pours where the surface dries fast.
- Color integral and sealers: Pigment mixed into the concrete rather than applied on top, so it doesn’t wear off at the tire tracks. Sealing runs $250 – $700 and needs redoing every few years; it’s the difference between a slab that looks new at year ten and one that looks tired at year five.
What Concrete Driveways & Concrete Work costs in Alamo, CA

Plan on $4,500 – $12,000 for a new concrete driveway in Alamo, and $5,000 – $14,000 if you’re replacing an existing slab and hauling the old one out. Five things push a job toward the top of that range:
- Square footage and width. A standard two-car drive is around 400 square feet. Alamo’s one-acre-plus lots often mean longer approaches from the street to the garage, and every extra 100 square feet adds roughly $800 – $1,200.
- Slope and grading. A flat drive needs almost no earthwork. A steep Stone Valley Road approach can require retaining, step-downs, and extra base, which adds $1,500 – $4,000 on its own.
- Existing slab condition. Thick old concrete, embedded rebar, or a slab poured over rubble all cost more to break out and haul.
- Permit scope. If the job touches grading, drainage, or the county right-of-way, permit and inspection fees apply and add time.
- Finish and reinforcement. Exposed aggregate and thicker reinforced pours sit at the high end; broom finish on a 4-inch slab sits at the low end.
A written estimate from us covers demolition, haul-off, base prep, forms, reinforcement, the pour, finish, and joint cutting. It doesn’t cover landscaping repair, drainage improvements like French drains, or any structural work uncovered during demo; those get quoted separately before anyone proceeds, so the price on the page is the price you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Alamo homes specifically do to this job
Alamo is unincorporated, which changes the paperwork before a single form goes in the ground. There’s no city building department here; permitting runs through Contra Costa County, and on hillside lots it often pulls in fire district review and county grading rules alongside the building plans. That’s a different review path than a homeowner in neighboring Danville or Walnut Creek would follow, and it’s why we build inspection time into the schedule from the start rather than discovering it mid-job.
The housing stock shapes the work too. Most of what we tear out on Alamo properties is original concrete from homes built in the 1960s through the 1990s, often cracked at the joints, settled at the garage apron, or heaved where tree roots pushed up from below. On the wooded ridges and the steep graded drives off Stone Valley Road, we’re regularly dealing with oak-tree preservation setbacks and well-and-septic clearances that constrain where a slab can go. Hot, dry Diablo Valley summers also mean we pour early in the morning and cure carefully, because concrete placed in 95-degree heat without the right mix and moisture control will crack before its first birthday. Fire-resistant detailing matters here as well, so we keep combustible material away from the slab edge and maintain defensible space along the drive. We cover the full 94507 and surrounding Alamo area.
Serving Alamo, CA – Our Local Coverage Area
We serve Alamo and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Concrete Driveways & Concrete Work in Alamo

Most concrete driveways in Alamo take 3 – 5 working days from demolition to final finish, then 7 days of cure before you drive on it. Larger hillside pours with grading and county inspection can stretch to 7 – 10 days. Call (855) 471-4163 and we’ll give you a firm schedule with your estimate.
Sometimes. A flat replacement slab in the same footprint usually doesn’t require one, but any job that changes grading, drainage, or the county right-of-way does, and Contra Costa County review applies because Alamo is unincorporated. We tell you upfront whether your job needs a permit and handle the paperwork when it does. Call (855) 471-4163 to find out where yours lands.
Only in narrow cases, and we don’t recommend it. Pouring over an existing slab traps moisture, adds dead weight, and inherits every crack underneath. A proper job means removing the old concrete and rebuilding the base, which is why replacement runs $5,000 – $14,000 rather than installation pricing. Call (855) 471-4163 and we’ll tell you honestly whether a pour-over is even viable on your lot.
New concrete driveways run $4,500 – $12,000 and full replacements $5,000 – $14,000, with slope, square footage, and finish driving the difference. Sealing afterward adds $250 – $700. Call (855) 471-4163 for an exact quote, and the estimate is free.
Every concrete job we do is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it’s in writing before we break ground. Call (855) 471-4163 to schedule your estimate.
If the driveway is part of a larger exterior plan, homeowners often pair this with ADU Site Prep & Utilities in Alamo, Door Installation in Alamo, or a broader Driveway & Pavers in Alamo project, and we’re glad to scope it all in one visit through our Driveway & Pavers service.
Get your concrete driveway estimate in Alamo
Call (855) 471-4163 for a free on-site estimate on Concrete Driveways & Concrete Work in Alamo. A live person answers around the clock, and we’ll set a time that works for you. On the visit we measure the drive, check the grade and drainage, confirm whether Contra Costa County permitting applies, and hand you a written line-item quote with the 730-Day Done Right Promise attached. No pressure, no surprises.
Written by the team at Groundwork Construction Co.












